Note* Click inside magnifer to see large image
Bona DTS (Deep Tone Sealer) is a specifically formulated waterborne sanding sealer that develops a vibrant look and deep, natural tone to individual wood species. The unique "wet look" appearance accentuates the natural pigmentation and color characteristics of the wood. GREENGUARD certified for indoor air quality.
- Unique "wet look" appearance adapts to the individual wood species, accentuating the natural pigmentation and color characteristics
- Excellent sandability – hardens rapidly and allows for easy abrasion
- Seals the wood, preventing the finish from penetrating
- Reduces tendency for sidebonding
- Exceptional flow and leveling of finish top coats
- Fast drying – 2-3 hours
- GREENGUARD certified for indoor air quality
- Nonflammable
- Water clean-up
- Product can be rolled or pulled with a t-bar
Commercial wood floors
For use on newly sanded wood floors
Technical Data
Physical Characteristics: |
|
| Ingredients | Water, polymeric resin, silica derivate, diethylene glycol monoethyl ether, and polysiloxane. |
| Color | Milky white (wet) |
| pH | 7.5 - 7.9 |
| Solids | 31-32% |
| Density | 8.66 lbs/gallon (1.04 S.G.) |
| US Regulatory VOC | 250 g/L |
| Odor | Non-offending |
| Packaging | 1-gallon plastic bottle |
Application Characteristics: |
|
| Clarity | Clear when dry |
| Leveling | Excellent |
| Defoaming | Excellent |
| Drying Time | approximately 2-3 hours (high humidity and/or low temperature conditions will extend the drying time) |
| Coverage | 450-600 square feet per gallon |
| Percent Cured After 24 Hours | N/A |
| Maximum Cure | 100% after 1 week |
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
COMPATIBILITY: Stain, sealer and finish results may vary widely depending on the wood species, especially on oily and resinous Exotics. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS:
- Sand and prepare floor using accepted industry association methods.
- For a stained floor, make your final cut with 80-100 grit paper and screen to 80-100 grit. For an unstained floor, make your final cut with 80-100 grit paper and disc/screen to 120-150 grit. This burnishing will reduce the amount of grain raise.
- Use a Tampico Brush on a buffer and vacuum thoroughly.
- Tack with a dry Bona Microfiber Mop or cloth to remove dust.
- Apply finish system.
THE BONA DTS SYSTEM: Apply 1-2 coats of Bona DTS and 2 coats of a Bona waterborne finish. Bona DTS is not needed when using a Bona stain with a Bona waterborne finish. Bona DTS minimizes side-bonding and grain raise, provides a build layer and prevents the finish from penetrating into the wood surface. Visit www.bona.com for additional product information.
RECOMMENDED APPLICATORS: Bona Floor Coater (T-bar), Bona Roller, Bona Cut-In Pad.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: SHAKE WELL BEFORE USING – DO NOT THIN. DO NOT ADD WATER. Insert supplied filter.
SEALING:
- Pour a 4" wide line of sealer along the starting wall. Go with the grain of the wood.
- Using a pre-dampened T-bar sleeve, draw the applicator forward with the grain of the wood, moving the sealer toward the opposite wall. To maintain a wet edge at all times, hold the applicator at a snowplow angle.
- At the end of each run, turn the applicator towards you and pad out the applicator parallel to the wet edge.
- Feather out all turns. Do not push too hard or too fast to avoid drips flying off the applicator.
- BE SURE YOU ARE USING THE RECOMMENDED COVERAGE OF 450-600 SQ. FT. PER GALLON. DO NOT SPREAD TOO THIN.
- Allow the first coat to dry 2-3 hours. High humidity and/or low temperature conditions will extend the dry time recommended conditions of 65-80° F (18°C-27°C) 40-60% relative humidity).
- For smoothest results, abrade before applying finish coats. Always vacuum and tack thoroughly with a slightly water dampened Bona Microfiber Mop or cloth after abrading.
INTERCOAT ABRASION: It is not necessary to abrade DTS unless more than 48 hours has passed since the previous coat was applied. However, for smoothest results, abrade the DTS sealer coat with a Bona Conditioning Pad and 1-2 Delta sheets as needed or a 150 grit or finer screen. Always vacuum and tack thoroughly with a slightly water-dampened Bona Microfiber Mop or cloth after abrading.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
STABILITY: One year shelf life in unopened container.
STORAGE: Nonflammable Bona DTS should be stored in a climate-controlled environment.
KEEP FROM FREEZING. Do not store above 100º F.
INGREDIENTS: Water, polymeric resin, silica derivate, diethylene glycol monoethyl ether, and propylene glycol.
Please recycle container when empty.
Similar products in case you want to buy similar or just want to know
Top coat to be used with. It is recommended by it manufacturer and advised by our customers.
Stain to be used with. It is recommended by manufactures or our customers. Please read direction of manufacturer to avoid trouble.
| Currently viewing: |
-1181.jpg?osCsid=rd1ov86cub40e7h3ttaf9h03e1 "Bona Traffic Waterborne Wood Floor Finish One Gallon")
