Note* Click inside magnifer to see large image
- Description
- Specifications
- Professional View
- Similar Products
- Sealers to Use
- Tools to Use
- Maintenance After
- Stains
- Screen / Abrasive
- Wood Putty
Basic Coatings Street Shoe Water based Wood Floor Finish
The fastest-curing finish on the market, StreetShoe is the industry benchmark for waterbased finishes. Available in three sheens. Ideal for all commercial, sports and residential applications. Our price includes the Basic Coatings StreetShoe hardener/catalyst and a handy strainer cap.
Gloss 731648000267
Semi-Gloss 731648000274
Super Matte 731648000298
B0680-4312/ Gloss/ 731648000267
B1644-4312/ Semi-Gloss/ 731648000274
B1645-4312/ Super Matte/ 731648000298
- Fastest cure available; 90% cured in 24 hours.
- Ultra smooth flow and leveling. Non-foaming and non-streaking formula.
- Excellent durability.
- 24-hour pot life.
- UV inhibitor minimizes wood color change.
- Can be re-catalyzed for use as an initial coat on another job.
B1645 StreetShoe Super Matte MSDS English
B1643 StreetShoe Satin MSDS English
B0680 StreetShoe Gloss MSDS English
- COMMERCIAL
- RESIDENTIAL
- SPORTS
- WOOD FLOOR TOPCOAT
Tech Specification
| Color | Clear |
| Coverage | 500 - 700 sq ft/gal |
| Dry time | 2 - 3 hours |
| Recoat window | 2 - 24 hours |
| Pot life | 24 hours |
| Shelf life | 1 year |
| Light traffic | 24 hours |
| Full cure | 7 days |
| Rugs | 2 weeks |
| VOC | Less than 350 grams/liter |
RECOMMENDED SYSTEMS
Full Sand - 2 coats Commercial Catalyzed Sealer, Hydroline Sealer, Lock 'N Seal, Emulsion + 1-2 coats StreetShoe Recoat – 2 coats StreetShoe or use TyKote Dustless Recoating System with 1-2 coats StreetShoe
OVER STAIN
Allow oil stains to dry per manufacturer's directions or longer depending on environmental conditions. Apply 2 coats of Commercial Catalyzed Sealer, Emulsion, or Lock 'N Seal followed by StreetShoe. To avoid tannin pull, use Lock 'N Seal as a sealer. A test board is recommended with any stain to insure compatibility and color acceptance.
ADDING WATER
Up to 12oz of water can be added per gallon of finish. Adding water will increase the flow and level time during situations of high temperature and low humidity.
SURFACE PREPARATION
- Before sanding, clean the floor using Basic Squeaky Cleaner following label instructions. Cleaning should be done to remove contaminants from the floor before sanding.
- Sand floors using accepted NOFMA/MFMA procedures. All old finish must be removed. A NIOSH approved dust mask should be worn during sanding.
- Finish sanding with a new 120-grit screen. DO NOT USE STEEL WOOL.
- Vacuum. Tack with a clean, dry Basic microfiber mop until all dust has been removed.
- Apply 2 coats Commercial Catalyzed Sealer, Hydroline Sealer, Emulsion, or Lock 'N Seal according to label instructions.
MIXING XL CATALYST
- Use a stir stick to re-disperse any settlement. Rock container several times.
- While stirring finish, slowly add one 3-ounce bottle XL Catalyst per gallon of StreetShoe. For 5-gallon pail, slowly add one 13-ounce bottle XL Catalyst to pail while stirring. Continue mixing for 30 seconds before pouring into pour can.
- When catalyzed material is over 24 hours old. Refer to Technical Bulletin for "Re-Catalyzing StreetShoe". XL Catalyst can irritate skin and eyes upon contact. Wear proper protection.
FINISH APPLICATION
Always maintain adequate ventilation during all phases of the coating and drying process.
- Measure moisture content of floor in several areas. We recommend using a Wagner Dual Depth L607 Moisture Meter or equivalent.
- Rinse refill applicator and remove all excess water. This helps to remove loose fibers.
- Edge out about 6 inches from the baseboard or wall with a paint pad or polyester brush. Stay within 2-3 feet of the puddle line to avoid lap marks, streaking or thicker film build. Be sure to feather the edge.
- Starting about one foot from the head wall, pour a 4-inch wide line of finish the length of the floor going with the grain. Stop about three feet from the opposite wall. As close to the wall as possible, hold the applicator at a slight angle and drag it in a "squeegee" or "plowing" type motion to move the puddle from one side of the room to the other. Overlap two inches of last pass and pull parallel passes until the entire floor is coated. Brush out all turns, stops, and other applicator marks brushing in the direction of the puddle-line. Feather out turns with a painters pad after the tbar has made the turn. Add finish to the puddleline when needed to maintain a wet edge across the room.
- When 2-3 feet from exiting wall, begin to taper the puddle-line down to a nickel size bead. Back out of the room by wetting small sections of the remaining floor, brushing away from you in the same direction as the grain of the wood.
- Allow each coat a minimum of 30-45 minutes to level.
- After finish levels, place fans in an adjacent area to pull moisture away from the job site. When each coat has dried a minimum of 2-3 hours, remeasure moisture content. If moisture content is not equal to the first reading, allow more dry time before proceeding to the next coat.
- If necessary, abrade between coats to remove debris, hair, drips, etc. or if the 24-hour window between coats has elapsed. Abrade with the pad and strip system using 180 - 240 grit sanding strips. Vacuum and tack with the Basic Microfiber Mop in between coats.
- If the 24-hour window has elapsed, the TyKote Dustless Recoating System is an alternative to screening the floor. Refer to TyKote application procedures for details.
- Apply second coat in the same manner.
RECOATING PROCEDURES
NOTE For fast, easy recoating, try Basic's TyKote Dustless Recoating System. The TyKote system is compatible with most urethane finished floors and doesn't require screening.
Refer to TyKote directions for complete details.
- DO NOT USE StreetShoe over waxed surfaces. See technical bulletin, "Testing for Waxes and Polishes".
- Tack the floor with Basic Squeaky Cleaner and the Basic Microfiber Mop following label instructions.
- Abrade with a new 100 or 120 grit screen. Make sure all shine is screened from the floor. DO NOT
USE STEEL WOOL. - Vacuum. Tack floor with a Basic Microfiber Mop lightly dampened with water or Squeaky Cleaner solution until all dust has been removed.
- Apply two coats of StreetShoe using the procedure described above.
DRY TIME
Allow at least 2-3 hours between coats and 1 hour of good ventilation before closing job site. Keep air moving over floor for several hours. The floor may be opened to light traffic and furniture replaced after 24 hours dry time, however, it is susceptible to scuffing or marring. Finish will reach full cure in approximately 7 days. Do not place carpet, rugs, or cover the finish for at least two weeks after completion of coating.
DAILY MAINTENANCE
Do not use any liquid cleaners other than water for the first 2 weeks. Use Basic Squeaky Cleaner as directed for routine cleaning and maintenance once the 2-week window has passed. See Basic's maintenance brochures for additional instructions.
DAILY MAINTENANCE
Do not use any liquid cleaners other than water for the first 2 weeks. Use Basic Squeaky Cleaner as directed for routine cleaning and maintenance once the 2-week window has passed. See Basic's maintenance brochures for additional instructions.
Similar products in case you want to buy similar or just want to know
Sealers what can be used with.
Tools to be used with this product.
Products for maintenance after applied
Stain to be used with. It is recommended by manufactures or our customers. Please read direction of manufacturer to avoid trouble.
Screen to be used with. It is recommended by manufactures or our customers. Please read direction of manufacturer to avoid trouble.
Wood Fillers/Putty what can be used with.
| Currently viewing: |
-1181.jpg?osCsid=og3s3k8rro2374vjg9i4271fe2 "Bona Traffic Waterborne Wood Floor Finish One Gallon")
